开关失灵是许多电动门常遇到的问题。遇到这种情况，我们通常需要先了解其开门失业的原因，然后再根据具体原因解决问题。通常来说，悬浮门无法打开或无法关闭怎么办有以下这几种情况：
Switch
failure is a common problem encountered by many electric doors. When
encountering this situation, we usually need to first understand the
reasons for their unemployment, and then solve the problem based on the
specific reasons. Generally speaking, there are several situations where
a suspended door cannot be opened or closed:
一：该开不开，该关不关。
1： Should it be turned on or off.
这种现象可以理解为“该打开的时候打不开，该关闭的时候却又关不上”。当行人通过悬浮门时，悬浮门关闭。当行人从悬浮门出来时，悬浮门本来应该是开结果还是关不上。
This
phenomenon can be understood as' unable to open when it should be
opened, but unable to close when it should be closed '. When pedestrians
pass through the floating door, the floating door closes. When
pedestrians come out of the floating door, whether the floating door
should have opened or could not have closed.
造成这种现象的原因是工家庄电动伸缩门 保定桌椅 保定水处理设备 河北机械加工 保定养老院 保定防水人在维修或安装悬浮门时，电源带反了。解决这种现象的方法是改变扣带的上下位置，或者更换控制器。
The
reason for this phenomenon is that workers have reversed the power
supply when repairing or installing the suspended door. The solution to
this phenomenon is to change the up and down positions of the buckle or
replace the controller.
二：防夹功能有问题。
2： There is a problem with the anti pinch function.
悬浮门具有防夹功能。如果悬浮门因障碍物或严重碰撞而不能正常关闭3次以上，悬浮门将自动停止移动，即停止其开启和关闭。遇到此问题，只需将悬浮门推至全开状态即可。
The
suspended door has an anti pinch function. If the suspended door cannot
be closed normally more than 3 times due to obstacles or serious
collisions, the suspended door will automatically stop moving, that is,
stop its opening and closing. When encountering this problem, simply
push the floating door to the fully open position.
三：遥控器惹的祸。
3： The remote control caused trouble.
悬浮门可能无法关闭。这可能是由于遥控器上的锁定操作不当造成的。这时候只要用遥控器解锁就可以了。
The
floating door may not close. This may be caused by improper locking
operation on the remote control. At this point, just use the remote
control to unlock it.
四：电源问题或卡死。
4： Power supply issue or stuck.
这种现象是悬浮门接通电源后，无论是打开还是关闭都没有反应。出现此问题的原因可能是悬浮门未通电。卡可能被卡住或控制器可能崩溃。要解决此问题，请检查电源 LED 是否亮起，然后拉动挡板并检查它是否已拉动。
This
phenomenon is that after the suspension door is powered on, there is no
response whether it is opened or closed. The reason for this issue may
be that the suspension door is not powered on. The card may be stuck or
the controller may crash. To solve this problem, check if the power LED
is on, then pull the bezel and check if it is pulled.